当前位置:金沙国际官网-新闻中心 > 新闻中心

金沙国际官网生产过程中的失误解决措施都有哪些?

发布人:   发布时间:2020-03-24 16:20:24

金沙国际官网是通风空调系统的重要组成部分。但是由于种种原因,可能会导致管道的处理问题,下面就来了解一下有哪些问题。

  Ventilation duct is an important part of ventilation and air conditioning system. However, due to various reasons, it may lead to pipeline processing problems. Let's see what problems exist.

  1. 加工材料不符合标准

  1. Processing materials do not meet the standards

  性能:板材表面不平整,厚度不均匀,有明显的压痕、裂纹、砂痕、疤痕、锈斑等。风道平面下沉,侧面向外突出,有明显变形。

  Performance: the surface of the plate is not smooth and the thickness is not uniform, with obvious indentation, crack, sand mark, scar, rust spot, etc. The plane of air duct sinks, the side protrudes outwards, and there is obvious deformation.

  影响:运行中风道泄漏,空调负荷增加,同时影响风的寿命和性能。

  Impact: air duct leakage during operation, air conditioning load increases, while affecting the life and performance of the air.

  原因:材质不合格,不能满足生产风管的需要。

  Cause: the material is unqualified, which can not meet the needs of production air duct.

  措施:使用管道加工设备制作管道前,应先检查材料厂证书、材料合格证、外观厚度等,确保材料的可用性。

  Measures: before using the pipeline processing equipment to make the pipeline, the material factory certificate, material certificate, appearance thickness, etc. shall be checked first to ensure the availability of materials.

  二、风管翘曲角度和弯头角度不允许

  2、 Duct warping angle and elbow angle are not allowed

  性能:矩形风管两个相对平面,两端不平行;折叠角度不直;对角线不相等;宽松的咬人。

  Performance: two relative planes of rectangular air duct, the two ends are not parallel; the folding angle is not straight; the diagonal is not equal; loose biting.

  影响:会使气管连接力不均匀,安装后气管不直,法兰垫片不紧,漏风系统,空调负荷损失,并缩短使用寿命。

  Influence: it will make the connection force of air pipe uneven, the air pipe is not straight after installation, the flange gasket is not tight, the air leakage system, air conditioning load loss, and shorten the service life.

  原因:板材落料放样不准确;风道两边平行,对边的纸长和宽度不相等。

  Cause: the blanking and setting out of the plate are not accurate; both sides of the air duct are parallel, and the paper length and width on the opposite side are not equal.

金沙国际官网

  措施:下料时,板材角度应严格保持正方形,并检查各板材的长、宽、对角线,使其偏差控制在允许范围内;板材落料后,风道对面的两块板材应重合,以检查尺寸的准确性。

  Measures: when blanking, the angle of the plate shall be strictly square, and the length, width and diagonal of each plate shall be checked to make its deviation within the allowable range; after blanking, the two plates opposite the air duct shall be overlapped to check the accuracy of the size.

  因此,为了生产出实用耐用的优质风管,必须在风管加工设备运行前后进行充分的预置和运行准备,以保证无故障,减少不必要的损失。

  Therefore, in order to produce a practical and durable high-quality air duct, it is necessary to carry out sufficient preset and operation preparation before and after the operation of the air duct processing equipment, so as to ensure no failure and reduce unnecessary losses.

  以上就是对金沙国际官网生产过程中失误的解决措施的详细介绍,想要了解更多请点击官网

  The above is a detailed introduction to the solutions to the mistakes in the production of Jinan ventilation pipeline. For more information, please click


上一篇:金沙国际官网应用范围是否广泛?
下一篇:最后一页

金沙国际官网 关于我们 产品展示 新闻中心 工程案例 在线留言 联系我们

Baidu
sogou